Requirements

A computer with 1 free full duplex network card
Linux where C programs can be compiled.
Bertest installed

Network card (NIC) setup

Set up full duplex and 10Mbps with autonegotiation disabled. Full duplex hints. The most used ones:

mii-diag -F 10baseT-FD eth?
mii-tool -F 10baseT-FD eth?
ethtool -s eth? duplex full

Get rid of any traffic into the NIC

Kill all running dhcp daemons running on the interface (possibly ps ax | grep dhcp to list them).
Remove IP address (possibly ifconfig eth? 0.0.0.0)

Postscript / PDF / EPS / BIG png / SVG (Inkscape)

Connecting a Twister

If you have a Twister, connect Ronja Twister to the NIC and set it to "Loopback" position. You don't need to connect Twister to power.

Postscript / PDF / EPS / BIG png / SVG (Inkscape)

Connecting a Twister2

Connect Ronja Twister2 to the NIC and set it to the "Loopback" position. You don't need to connect the Twister2 to power.

Running pktloss

If your input and output network card is eth0, run pktloss. If eth1 is input and output, run pktloss eth1. If eth1 is output and eth2 input, run pktloss eth1 eth2.

No DUT connected

In such a case the output will be like this:

1102885167.075454000    100.000 100.000 1024    2224
1102885167.645578000    100.000 100.000 1024    2224
1102885168.215306000    100.000 100.000 1024    2224
1102885168.785415000    100.000 100.000 1024    2224
1102885169.355167000    100.000 100.000 1024    2224
1102885169.925561000    100.000 100.000 1024    2224

Second and third column show packetloss at 10MHz and 5MHz.

Device with packetloss connected

In such a case the output will look like this:

1102885377.652586000    13.868  77.637  1024    2224
1102885378.222727000    14.649  80.372  1024    2224
1102885378.792451000    17.969  83.692  1024    2224
1102885379.362579000    17.188  85.157  1024    2224
1102885379.932404000    22.364  84.961  1024    2224
1102885380.502458000    15.528  79.883  1024    2224
1102885381.072232000    13.379  76.661  1024    2224
1102885381.642390000    15.918  75.196  1024    2224
1102885382.212091000    12.793  87.012  1024    2224

Second and third column show packetloss at 10MHz and 5MHz.

Measurement

Choose output filename describing the measurement you are doing, we'll use example.dat for example. Let it run with output redirected into a file this way for a couple of minutes:

bertest <arguments> > rx_1.dat

Running GNU R

Now run ./analyze example.dat (replace example.dat with your datafile name). example.ps and example.pdf will be generated.

Packetloss in PDF/PostScript output

Display the resulting Postscript or PDF and go to page 11. There you can see filtered measurement of the packetloss. Read the higher value of the two. Unfiltered values are on page 1.

Evaluation of packetloss

There should be practically no packetloss. Any packetloss indicates that something is wrong with the electronics.

Measuring packetloss of Twister, Twister2 on loopback using Bertest